本帖最后由 luzhanyi 于 2014-11-21 10:36 编辑
转自Overclock.net论坛
http://www.overclock.net/t/1517316/extract-and-flash-gtx-970-and-980-firmware-gpuz-test-build-and-new-nvflash-5-190/80#post_23037661
All credits to JoeDirt and Welly59
Update:
http://www.overclock.net/t/15173 ... mits-and-gamestable
原PO主的每一个zip里面都包括了NVflash5.196+MBT1.36以及更改的bios和原版的evga的bios(原po是用的evga的)
这边放出了不少970/980的BIOS,有2个版本,GS=GAME STABLE.另外一个是nolimits
简单的说GS比较稳定(相对来说,不适用于所有卡,毕竟体质不太一样),nolimits的适合极限超频跑分
建议大家下下来自己对比着修改自己的bios比较好,互刷容易卒
并且华硕,索泰的显卡似乎电压修改不能,因为自己的特别的技术导致电压控制器貌似不通用...
反正我的strix 970只能跑1.2125v (软件度数,GPUZ/AIDA64/HWINFO64...没仪器)
按照po主的bios来修改自己的,刷了之后我的970可以boost到1506,这会儿在公司,晚上回家上图
原PO主的Power Table的设置的解释:
"TDP - Typical Dynamic Power
Internal Rail - I'm not exactly certain what this rail is used for, but it's the same on ALL the 980 BIOS's I looked at, including the high end factory overclocked cards.
PCI-E - Power the GPU will draw off the PCI-E socket, don't exceed 75000!
PSU Rail1 & 2 - 6 pin cards will be set to ~75000, but since we know 8pin is just a 6pin with 2 more grounds, you can increase this to as much as 200W depending on the PSU. (200W at 12v = ~17A current draw)
Power Target - This is how you increase the nominal operating power. This also represents the slider in Afterburner, etc. Max should match Max of TDP.
If you set your Max TDP and Power Target higher than the combined power of your rails, you will never be able to reach the specified TDP/Power Target.
So, Remember: PCIE + PSU Rail1 + PSU Rail2 = Max TDP/Power Target"
大概说下翻译的:
TDP跟power target就不说了, Internal Rail不清楚是啥,但是原PO表示所有的980的bios里面都一样的,包括最高端的预超的高频卡
PCI-E 这个是GPU从PCIE插槽接受的:不要超过75000单位是mw
PSU Rail 1&2, 6pin的是75000,因为8pin只是比6pin多了2跟地线,可以增加这个到最多200W,根据电源来(200w @12v就大概17A电流)
如果设置的最大TDP跟Power Target比其他的供电加起来还高,就永远不会达到特定的TDP/power target
所以: PCIE+PSU Rail 1 + PSU Rail 2 = 最大TDP/Power Target
MBT1.36在41L的朋友的附件里
注: 这个是Maxwell II Bios Tweaker理论上只支持980/970的,GM107的请继续使用KBT
修改跟刷bios有风险。。。不明白自己在做什么的就别看了。。。自己对自己的东西负责
任何损坏请自行承担责任
Maxwell II Bios Tweaker:
可以正确识别970的bios(用GPUZ 1.8提取的)
只修改了TDP上限跟显存频率,并且成功刷上了显卡bios
GPUZ截图:
Nvidia inspector里面也可以正确识别187%的tdp
Msi Afterburner跟asus自己的GPU Tweaker也可以识别到187%的TDP
刷之前需要先进入设备管理器中禁用显卡驱动,然后再刷新,刷完再启用显卡驱动,目前只知道显存修改了需要重启生效,其他修改应该重新启动驱动之后就生效
跟之前的nvflash用法一样,用cmd进入然后nvflash -6 bios.rom,然后确认2次(如果是别的显卡的bios可能会有第三次)
还是那句话。。。折腾有风险,请自己承担责任
update:
电压修改貌似还有问题...
试着修改了显存频率跟BOOST TABLE,现在默认1.212V电压可以boost到1530Mhz
可以完全无问题跑3Dmark
|