美光官方论坛大量反映010G固件引起掉盘

看来这版固件问题不小，很多人掉盘了（包括我），而且不光是UEFI平台
美光官方人员仍坚称只是升级程序不支持UEFI，固件没问题
目前玩家总结的解决办法是降级000F
http://edge.crucial.com/firmware/m4/000F/Crucialm4_000F.zip

System: Dell Optiplex 390 Intel H61 SATA 3G , UEFI Bios disabled. The SSD ist not recognized during 9 of ten reboots.
When it was recognized i flashed back to 000F and Problems goes away!

I can confirm that it makes the drive undetectable under UEFI (I was testing out some other things, just so happens I ran into the issue).

Updated my M4, worked fine until I went for lunch. Came back to find laptop totally frozen. Had to shut it down via the power button and now when I start it, it says there's no boot device.
Looks like it bricked my SSD. This is a big issue for me since my laptop is the only PC I have access to at work so I don't know what to do now!
I returned smoothly to 000F version because I do not trust. In my country,Spain, in hardware forums some people have had problems later with UEFI bios, disk not recognized.

So, here i am on 010G and my M4 256 Gb is not recognized By the bios.  My MB is Asus RIVE..

Sweet.. I removed some devices from my boot order in the BIOS and the BIOS wouldn't detect the drive. This is the first time ever I had a problem with the detection of the drive. After about 10 reboot tries it finally detected the drive and booted.
This is some improvement in drive detection by gosh.
I WANT CRUCIAL TO TELL ME HOW TO DOWNGRADE THE BIOS TO 0F. THIS IS COMPLETELY UNACCEPTBLE!
My board is a Asus P8Z68-V PRO/GEN 3 and the BIOS is Rev 3402.

Hi all
big problem for me after upgrading my M4 256 Go with firmware 10G.
My ssd doesn't start when I start my computer
I must wait 10 minutes (pc started) and My ssd is detected by the motherboard and the system starts normally.
the behavior is the same whatever the sata port (marvell sata 3 or intel sata 2).
It s very annoying.
After starting , no problem , the ssd works fine.
any ideas on the problem ?

Same problems here. Downgrade with ISO 000F works...
Win7 crashed after 2 hours on 010G.
SSD was not found in AHCI mode anymore
I expected a HW defect.
So i tried to go back to IDE. Now M4 was detected again.
Flashing back to 000F. Enable AHCI and all ok.
I have an older board.
Gigabyte GA-965P-DS3

Updated from 09 FW my 256GB M4 with the serial number 1131031603DB
Update was fine - worked sucessfully using the Windows Updater Tool.
PC rebootet and Windows ran fine - second reboot, no BIOS can detect the SSD any more, not in IDE, not in AHCI but it seems like the PC can find a device connected to that SATA Port but not initialize.
I already checked the SSD in a second PC, same problem, none of my BIOS can detect the SSD sucessfully.

刚出了010G就升级了 因为自从上个鸡血固件以后 挺信任镁光的 结果最近频繁掉盘 来论坛看看才知道不是个案 没办法只好降级000F固件了 希望这次不会再有问题 多谢楼主
台式机X58+i7 960 应该是和什么UEFI无关

晕死，这年头就没有靠谱的ssd了吗？都有各种要命的问题

MS买回来就是000F的   还好没有手贱刷了。。我是更新控。。

第二次掉盘，刚到手时是0009固件，经常蓝屏，后来刷了000F固件，一个月前掉盘后通电恢复，恢复后刷了010G，前几天再次掉盘，无法30分钟通电修复，没办法只好发回商家返厂了，哭死了，镁光太垃圾，后悔买了镁光的固态盘啊。。。。。。。。。。。。。
补充下：联想f31a的本本，pm965，phoenix bios，固态盘接原硬盘位，500g机械盘接原光驱位

刷完010g直接掉盘，30min无法复活，直接退回换了一块。。。

昨天第二次掉盘，第一次000f固件，第二次010固件，看来与固件没关系，是镁光的硬件问题！

我的c400 64G，去年7月入手，前不久掉过一次，通电30分后正常，当时使用的是000f的固件，正常后马上去官网下了010g，没想到昨天又掉，看了各位兄弟的帖子判断应该与固件没关系，是镁光的硬伤！！

m4 256g 华擎z77  刚吊盘 在恢复中。。恢复好了果断000F 海淘的没保修伤不起

NND，害我把M4 64GB拿去返修了。

早已刷回000F！

俺是9月26日为俺的M4/128GB刷的010G。当别人的盘纷纷“落地”时，俺的盘颇老实，暗想，说不定俺的盘就是个例外。然而，今天早上这个盘终于赶上大部队了。

插电等侯苏醒。

我的华硕玩家国度r4e主板，镁光128g 固态硬盘，要掉盘，已刷回000f了，看来镁光又要升级固件了

技嘉，刷完固件后，掉过一次，EFI自启动项找不到SSD，但可以手动强制用SSD启动，再重启，就能找到，然后一直没事

我的主板华擎H67，刷完固件第一次重启后掉盘，BIOS中检测不到SSD，但两次重启后就一切正常，之后到现在也再没发生过掉盘问题，整个过程也没有“半小时大法”那么长时间，大概也就3、5分钟的样子。

已经刷回000F

刚才我也掉盘了，笔记本，系统为win8 RTM，传统bios，看到对win8有优化，010G一出就刷了，吃完饭回来发现屏幕点不亮了，但foobar还在放音乐（煲耳机），直接按关机键，重启就找不到盘了，通电30分钟后重启恢复，看来得先刷回000F了

观望中。。。大半年出来一个固件还是有问题

已经刷回000F

z77 3570k早上开了虚拟化找不到盘了，关掉后也不行，晚上回去拔数据线半小时试试。