美光官方论坛大量反映010G固件引起掉盘

看来这版固件问题不小，很多人掉盘了（包括我），而且不光是UEFI平台
美光官方人员仍坚称只是升级程序不支持UEFI，固件没问题
目前玩家总结的解决办法是降级000F
http://edge.crucial.com/firmware/m4/000F/Crucialm4_000F.zip

System: Dell Optiplex 390 Intel H61 SATA 3G , UEFI Bios disabled. The SSD ist not recognized during 9 of ten reboots.
When it was recognized i flashed back to 000F and Problems goes away!

I can confirm that it makes the drive undetectable under UEFI (I was testing out some other things, just so happens I ran into the issue).

Updated my M4, worked fine until I went for lunch. Came back to find laptop totally frozen. Had to shut it down via the power button and now when I start it, it says there's no boot device.
Looks like it bricked my SSD. This is a big issue for me since my laptop is the only PC I have access to at work so I don't know what to do now!
I returned smoothly to 000F version because I do not trust. In my country,Spain, in hardware forums some people have had problems later with UEFI bios, disk not recognized.

So, here i am on 010G and my M4 256 Gb is not recognized By the bios.  My MB is Asus RIVE..

Sweet.. I removed some devices from my boot order in the BIOS and the BIOS wouldn't detect the drive. This is the first time ever I had a problem with the detection of the drive. After about 10 reboot tries it finally detected the drive and booted.
This is some improvement in drive detection by gosh.
I WANT CRUCIAL TO TELL ME HOW TO DOWNGRADE THE BIOS TO 0F. THIS IS COMPLETELY UNACCEPTBLE!
My board is a Asus P8Z68-V PRO/GEN 3 and the BIOS is Rev 3402.

Hi all
big problem for me after upgrading my M4 256 Go with firmware 10G.
My ssd doesn't start when I start my computer
I must wait 10 minutes (pc started) and My ssd is detected by the motherboard and the system starts normally.
the behavior is the same whatever the sata port (marvell sata 3 or intel sata 2).
It s very annoying.
After starting , no problem , the ssd works fine.
any ideas on the problem ?

Same problems here. Downgrade with ISO 000F works...
Win7 crashed after 2 hours on 010G.
SSD was not found in AHCI mode anymore
I expected a HW defect.
So i tried to go back to IDE. Now M4 was detected again.
Flashing back to 000F. Enable AHCI and all ok.
I have an older board.
Gigabyte GA-965P-DS3

Updated from 09 FW my 256GB M4 with the serial number 1131031603DB
Update was fine - worked sucessfully using the Windows Updater Tool.
PC rebootet and Windows ran fine - second reboot, no BIOS can detect the SSD any more, not in IDE, not in AHCI but it seems like the PC can find a device connected to that SATA Port but not initialize.
I already checked the SSD in a second PC, same problem, none of my BIOS can detect the SSD sucessfully.

顶楼主,支持新发现..
还好我是传统BIOS,避过一难

feve 发表于 2012-9-29 17:07
顶楼主,支持新发现..
还好我是传统BIOS,避过一难

底下有个965P老主板的人也掉盘了，不是个案

这兼容性的问题还真不好照顾全。。
继续000F吧，反正没啥问题现在

frontwing 发表于 2012-9-29 17:09
底下有个965P老主板的人也掉盘了，不是个案

  还是避难了,暂时用了两天没问题.
  
  还没刷的还是先看定情况比较好.

  不过刚经过求助区看到01G好象解决了兼容问题..
http://bbs.pceva.com.cn/thread-67931-1-1.html

其实吧  我一直在等待   等待大家反应再刷

128G的更新010G用了3天了，半夜也不关机，z77下木有发现掉盘

另一台老机P35 ICH9R上的64G也没问题～

现在救回来了，拔掉数据线通电半小时，关机再接上数据线，BIOS能认了
进系统刻录000F固件的盘，关机拔掉其他硬盘的数据线，只留M4和光驱，光盘启动刷000F，重启后正常

我的也掉过一次 不过关机后开机又好了。。

我在考虑要不要刷了。今天刚入手的。

frontwing 发表于 2012-9-29 20:30
现在救回来了，拔掉数据线通电半小时，关机再接上数据线，BIOS能认了
进系统刻录000F固件的盘，关机拔掉其 ...

  呵呵,30MIN复活大法哇...恭喜恭喜

说起来看到你名字让我想起在等乐园..明年2月,哎

feve 发表于 2012-9-30 01:19
呵呵,30MIN复活大法哇...恭喜恭喜

说起来看到你名字让我想起在等乐园..明年2月,哎 ...

其实前两部还放着没动

frontwing 发表于 2012-9-30 08:03
其实前两部还放着没动

那你喜欢哪部来用这名字的喔?

feve 发表于 2012-9-30 10:30
那你喜欢哪部来用这名字的喔?

hoshiuta

现在还没有具体的什么情况会掉盘的具体统计是吗？

128G的M4在010G下今天又掉盘了,主板是微星的H77，看来这固件是真不能用在UEFI BIOS的主板上面，现在刷回000F了。。。

我的传统BIOS下也出现掉盘了。现在刷回000F。

HM65的，联想Y460P。以前一直正常并且其中的AE值从35现在到了52。


什么原因影响其中的AE及AD值？

风火神 发表于 2012-9-30 18:42
128G的M4在010G下今天又掉盘了,主板是微星的H77，看来这固件是真不能用在UEFI BIOS的主板上面，现在刷回000 ...

所谓不支持UEFI是指不能在EFI启动的系统上更新这版固件，因为这版固件的更新程序是基于dos的，只能以传统bios方式启动后才能进入刷新程序，而且efi方式的启动是不能进入dos系统的

用UEFI但系统所在硬盘还是MBR的照样可以更新

p45很正常的说

我000f也突然掉盘过，30分钟大法救活。另外掉盘这种事跟uefi完全没关系，只不过windows下的固件更新程序不支持uefi而已