几条常用的ISDCT命令（Intel数据中心系列SSD工具箱）范例

只适用于Intel DC系列SSD（750可用，730不知道能不能用）

Display Tool Help ：

命令：isdct.exe help

Display Tool License：

Use the version command with the license property to display the End-User license agreement for Intel SSD Data Center Tool.

显示ISDCT的最终用户许可协议。

命令：isdct.exe version –d license

Display Drives:

Use the show command to display a list of drives on the system.

使用show命令显示系统上的驱动器列表。

命令：isdct.exe show –intelssd

Display Drive Info：

Use the show command’s –intelssd option to select which drive to execute functions on and provides a simple summary of each drive found. Use the show command’s –a –intelssd 1 option to display a verbose output of all the information the tool can get on that particular drive.

显示指定驱动器的详细信息。

命令：isdct.exe show –a -intelssd 1

Identify Device：

Use the show verb along with the –identify target to read and parse identify information. See Show Device Identification Structures for details.  

NOTE: Identify device contains a large amount of data and the console window may not be large enough to display it in a readable format

显示目标驱动器标识。

命令：isdct.exe show –identify –intelssd 1

      isdct.exe show –identify –intelssd 1 -nvmecontroller

Sensor or SMART data：

Use the -sensor command to read and parse the Health Sensors. Use the –smart command to read and parse the SMART attribute information of the selected drive.

显示驱动器SMART信息。

命令：显示所有Intel SSD SMART信息：isdct.exe show –sensor

      显示指定intel SSD SMART信息：isdct.exe show –smart –intelssd 1

Delete：

Use the Delete command to erase all the data on the drive.

删除驱动器上所有信息（安全擦除？）

命令：isdct.exe delete –intelssd 1

直接删除：isdct.exe delete –f –intelssd 1

Change Maximum LBA：

Use the MaximumLBA property to change the drive’s maximum storage capacity up to the native capacity of the drive (that is, MAX LBA).  NOTE: You should run the delete command before altering the Maximum LBA of a drive. After modifying the maximum LBA, a complete power shutdown is required to properly reflect the changes. The MaximumLBA property has four options: The native option resets the drive back to its native Max LBA, or 100% of the drive.

更改驱动器用户容量（手动OP功能），更改之前应先进行安全擦除，修改后需完全断电重启才能生效。共有4种更改方式。

命令：

The native option resets the drive back to its native Max LBA, or 100% of the drive.

直接指定最大LBA值，即100%容量。

isdct.exe set –intelssd 1 MaximumLBA=native

The LBA option specifies the drive’s max LBA with a specific number. The number entered must be a decimal literal.

直接指定LBA值（可按需查LBA表或自己计算）。

isdct.exe set –intelssd 1 MaximumLBA=xxxxxxxxxx

The x% percent changes the drive’s size based on a percentage of native max. Values of 1-100 are valid, where a value of 100 is equivalent to using the native option.

按照百分比指定用户可用容量，有效值1-100%。

isdct.exe set –intelssd 1 MaximumLBA=xx%

The xGB capacity option sets the drive to a specific capacity in gigabytes. This will result in an error if the given number of gigabytes is less than 1 or is greater than the drive’s max capacity.

直接按照GB指定用户可用容量，不得大于驱动器最大容量。

isdct.exe set –intelssd 1 MaximumLBA=xxGB

Update Firmware：

Firmware Update is achieved through the load command verb and is used to update the firmware of the selected drive:

固件升级。

命令：isdct.exe load -intelssd 1


附件:ISDCT使用说明（英文）

我说怎么装了没反应要命令行

大嫖客为了和大污贼交代一些事情，就发了这个帖子？

730和消费级optane都用不了

scoot 发表于 2018-10-13 22:06
大嫖客为了和大污贼交代一些事情，就发了这个帖子？

你猜对了

可以做op，功能很强大啊